 |
Pennsylvania Code (Last Updated: April 5, 2016) |
 |
Title 67. TRANSPORTATION |
|
PART I. Department of Transportation |
|
Subpart A. Vehicle Code Provisions |
|
Article VII. Vehicle Characteristics |
|
Chapter 159. New Pneumatic Tires |
Appendix A.
-
The following tables list tire sizes and tire constructions with proper load and inflation values. The tables group tires of related constructions and load-inflation values. Persons requesting the addition of new tire sizes to the tables or the addition of tables for new tire constructions may, when the additions requested are compatible with existent groupings, or when adequate justification for new tables exists, submit five copies of information and data supporting the request to the Secretary of Transportation, Attention: Motor Vehicle Programs, National Highway Traffic Safety Administration, U.S. Department of Transportation, Washington, D.C. 20590.
The information should contain the following:
(1) The tire size designation, and a statement either that the tire is an addition to a category of tires listed in the tables or that it is in a new category for which a table has not been developed.
(2) The tire dimensions, including aspect ratio, size factor, section width, overall width and test rim size.
(3) The load-inflation schedule of the tire.
(4) A statement as to whether the tire size designation and load-inflation schedule has been coordinated with the Tire and Rim Association, the European Tyre and Rim Technical Organisation, the society of Manufacturers and Traders Limited, the Japan Automobile Tire Manufacturers Association, the Deutsche Industrie Norm and the Scandinavian Tire and Rim Organisation.
(5) Copies of test data sheets showing test conditions, results and conclusions obtained for individual tests specified in this chapter.
(6) Justification for the additional tire sizes.
FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 109
TABLE I-ATIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR CONVENTIONAL AND LOW SECTION HEIGHT BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim width Minimum size Section width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) factor (inches) (inches) 6.00-13 … 770 820 860 900 930 970 1,010 1,040 1,080 1,110 1,140 4 29.37 6.00 6.50-13 … 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 30.75 6.60 7.00-13 … 980 1,030 1,080 1,130 1,180 1,230 1,270 1,310 1,360 1,400 1,440 5 31.88 7.10 6.00-14 … 840 900 930 980 1,020 1,060 1,100 1,130 1,170 1,210 1,240 4 30.64 6.10 6.45-14 … 860 910 960 1,000 1,010 1,080 1,120 1,160 1,200 1,240 1,260 4½ 30.92 6.60 6.50-14 … 930 990 1,030 1,080 1,130 1,170 1,210 1,250 1,300 1,330 1,370 4 31.75 6.60 6.95-14 … 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,310 1,350 1,390 5 31.96 7.00 7.00-14 … 1,030 1,100 1,140 1,190 1,240 1,200 1,310 1,380 1,430 1,470 1,520 5 32.88 7.10 7.25-14 … 1,040 1,100 1,160 1,210 1,260 1,310 1,360 1,400 1,450 1,490 1,540 5 32.92 7.30 7.50-14 … 1,150 1,230 1,280 1,340 1,390 1,450 1,500 1,550 1,600 1,650 1,700 5½ 34.19 7.65 7.75-14 … 1,150 1,210 1,270 1,330 1,390 1,440 1,500 1,550 1,600 1,650 1,690 5½ 34.09 7.75 8.00-14 … 1,240 1,320 1,380 1,440 1,500 1,560 1,620 1,670 1,730 1,780 1,830 6 35.17 8.10 8.25-14 … 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,670 1,730 1,780 1,830 6 35.11 8.20 8.50-14 … 1,330 1,420 1,480 1,550 1,610 1,670 1,740 1,790 1,850 1,910 1,960 6 35.91 8.35 8.55-14 … 1,360 1,430 1,510 1,580 1,640 1,710 1,770 1,830 1,890 1,950 2,000 6 36.06 8.50 8.85-14 … 1,430 1,510 1,580 1,660 1,730 1,790 1,860 1,920 1,990 2,050 2,100 6½ 36.82 8.95 9.00-14 … 1,430 1,510 1,580 1,660 1,730 1,790 1,860 1,920 1,990 2,050 2,100 6½ 36.91 8.80 9.50-14 … 1,540 1,640 1,700 1,780 1,850 1,930 2,000 2,060 2,130 2,200 2,260 6½ 37.74 9.05 6.00-15 … 890 940 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4 31.64 6.10 6.50-15 … 980 1,040 1,080 1,130 1,180 1,230 1,270 1,320 1,360 1,400 1,440 4½ 32.75 6.60 6.70-15 … 1,110 1,190 1,230 1,290 1,340 1,400 1,450 1,500 1,550 1,590 1,640 4½ 33.95 7.00 6.85-15 … 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,390 5 32.48 6.90 7.00-15… 1,170 1,240 1,310 1,380 1,450 1,515 1,580 1,640 1,700 1,760 1,820 1,870 1,930 5 36.02 7.35 7.10-15 … 1,190 1,270 1,320 1,380 1,440 1,500 1,550 1,600 1,660 1,710 1,760 5 34.89 7.40 7.35-15 … 1,070 1,130 1,180 1,240 1,290 1,340 1,390 1,440 1,480 1,530 1,570 5½ 33.86 7.50 7.60-15 … 1,310 1,400 1,450 1,520 1,580 1,640 1,710 1,760 1,820 1,800 1,930 5½ 36.05 7.90 7.75-15 … 1,150 1,210 1,270 1,330 1,380 1,440 1,190 1,540 1,590 1,640 1,690 5½ 34.53 7.65 8.00-15 … 1,380 1,470 1,530 1,600 1,670 1,730 1,800 1,860 1,920 1,980 2,040 6 36.84 8.30 8.15-15 … 1,240 1,300 1,370 1,430 1,490 1,550 1,610 1,660 1,720 1,770 1,820 6 35.50 8.15 8.20-15 … 1,470 1,570 1,630 1,710 1,780 1,860 1,920 1,980 2,050 2,110 2,170 6 37.50 8.50 8.25-15… 1,030 1,190 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,670 1,730 1,780 1,830 6 35.57 8.20 8.45-15 … 1,340 1,410 1,480 1,550 1,620 1,680 1,740 1,800 1,860 1,920 1,970 6 36.37 8.35 8.55-15… 1,220 1,290 1,360 1,430 1,510 1,580 1,640 1,710 1,770 1,830 1,890 1,950 2,000 6 36.57 8.45 8.85-15 … 1,430 1,510 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 37.29 8.80 8.90-15 … 1,700 1,810 1,880 1,970 2,050 2,130 2,210 2,290 2,360 2,430 2,500 6½ 39.54 9.30 9.00-15 … 1,460 1,540 1,620 1,690 1,760 1,830 1,900 1,970 2,030 2,090 2,150 6 37.45 8.50 9.15-15 … 1,510 1,600 1,680 1,750 1,830 1,900 1,970 2,030 2,100 2,160 2,230 6½ 37.92 9.05 5.00-16… 715 765 815 860 910 975 990 1,030 1,070 1,110 1,150 1,185 1,220 3 31.03 5.15 6.00-16 … 1,075 1,135 1,195 1,250 1,300 1,350 1,400 1,450 1,500 … 4 34.17 6.25 6.50-16… 1,090 1,150 1,215 1,280 1,345 1,405 1,465 1,525 1,580 1,635 1,690 1,740 1,790 4½ 35.59 6.80 6.70-16 … 1,185 1,240 1,300 1,355 1,410 1,465 1,525 1,580 1,635 1,690 1,740 1,795 4½ 35.60 7.40 7.00-16 … 1,365 1,440 1,515 1,585 1,650 1,715 1,780 1,840 1,900 … 5 37.02 7.35 7.50-16 … 1,565 1,650 1,735 1,810 1,890 1,960 2,035 2,105 2,175 … 5½ 38.78 8.00 6.50-17 … 1,215 1,275 1,330 1,390 1,450 1,500 1,560 1,620 1,680 1,740 1,795 1,850 5 37.00 7.60 L84-15 … 1,510 1,600 1,680 1,750 1,830 1,900 1,970 2,030 2,100 2,160 2,230 6 37.88 8.65 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the "dash".
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-B TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim width Minimum size Section width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) factor (inches) (inches) A70-13… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 5½ 30.27 7.30 B70-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 5 30.86 7.35 C70-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5½ 31.68 7.80 D70-13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.34 8.00 D70-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.81 7.85 E70-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.45 8.05 F70-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 5½ 34.16 8.30 G70-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.18 8.75 H70-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 36.19 9.10 J70-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 36.87 9.50 L70-14… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6½ 37.62 9.75 A70-15… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 30.99 6.60 C70-15… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,390 5½ 32.75 7.50 D70-15… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 33.37 7.70 E70-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 6 34.13 8.10 F70-15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6 34.89 8.35 G70-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.66 8.60 H70-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 36.64 8.95 J70-15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 37.36 9.35 K70-15… 1,290 1,380 1,460 1,540 1,620 1,690 1,770 1,830 1,900 1,970 2,030 2,090 2,150 6½ 37.66 9.40 L70-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6½ 38.09 9.60 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-C TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) “Super Balloon” Sizes 4.80-10… 320 355 390 430 470 490 510 535 555 575 595 … 3½ 23.90 5.00 5.20-10… 350 395 440 485 530 555 575 605 625 650 670 695 715 3½ 24.84 5.20 5.20-10… 385 430 475 515 550 580 605 630 650 675 700 … 4 24.00 5.80 5.20-12… 395 445 495 545 595 625 655 685 710 735 760 785 810 3½ 26.79 5.20 5.60-12… 460 520 575 620 670 715 760 795 825 855 885 915 940 4 27.83 5.71 5.90-12… 460 505 550 595 640 665 700 730 735 785 810 … 4 26.00 5.90 6.20-12… 505 555 605 655 705 735 775 805 835 865 895 … 4½ 27.00 6.30 5.20-13… 430 485 540 590 640 670 710 740 765 795 820 850 875 3½ 27.72 5.20 5.60-13… 495 560 620 675 725 770 810 850 880 910 945 975 1,005 4 28.92 5.71 5.90-13… 555 625 695 755 815 860 895 935 970 1,005 1,040 1,075 1,105 4 29.74 5.91 6.20-13… 520 580 640 700 750 780 820 850 880 910 945 … 4½ 28.00 6.30 6.40-13… 630 705 785 845 915 945 985 1,025 1,060 1,100 1,140 1,175 1,210 4½ 31.26 6.42 6.70-13… 690 775 860 935 1,000 1,045 1,090 1,135 1,175 1,220 1,260 1,305 1,340 4½ 32.14 6.69 6.90-13… 695 745 795 845 915 955 1,005 1,045 1,085 1,120 1,160 … 5 30.00 7.20 5.20-14… 475 535 595 645 695 735 785 825 855 885 915 945 975 3½ 28.89 5.20 5.60-14… 530 595 660 715 770 815 855 890 920 955 990 1,020 1,050 4 29.94 5.71 5.90-14… 585 660 730 785 850 880 925 970 1,005 1,040 1,080 1,115 1,145 4 30.76 5.91 6.40-14… 660 745 825 890 960 1,000 1,050 1,090 1,130 1,170 1,210 1,250 1,290 4½ 32.19 6.42 6.45-14 … 860 910 960 1,000 1,040 1,080 1,120 … 4½ 30.92 6.60 5.20-15… 505 570 630 685 740 780 830 870 900 935 965 1,000 1,030 3½ 29.75 5.20 5.60-15… 555 625 695 755 815 860 895 935 970 1,005 1,040 1,075 1,105 4 30.87 5.71 5.90-15… 615 695 770 825 890 935 980 1,015 1,070 1,090 1,130 1,165 1,200 4 31.77 5.91 6.40-15 … 875 950 1,010 1,055 1,100 1,150 1,190 1,230 1,260 … 4½ 33.20 6.42 “Low Section” Sizes 5.00-12… 370 420 465 505 540 565 580 605 625 650 670 695 715 3½ 25.62 5.04 5.50-12… 415 470 520 560 605 635 665 695 720 745 770 800 820 4 26.93 5.59 6.00-12… 485 545 605 655 705 735 785 815 845 875 905 935 965 4½ 28.33 6.14 5.00-13… 410 460 510 545 585 610 635 660 685 710 735 755 780 3½ 26.64 5.04 5.50-13… 445 495 550 595 640 670 710 740 765 795 820 850 875 4 27.95 5.59 7.25-13… 730 825 915 990 1,070 1,110 1,160 1,200 1,245 1,290 1,335 1,380 1,420 5 32.51 7.24 7.50-13… 775 875 970 1,040 1,120 1,180 1,225 1,270 1,315 1,365 1,410 1,460 1,500 5½ 33.22 7.48 5.50-15L… 505 570 630 675 725 760 800 840 870 900 935 965 995 4 29.97 5.59 6.00-15L… 595 665 740 800 860 890 930 970 1,005 1,040 1,080 1,115 1,145 4½ 31.29 6.14 6.50-15L… 675 755 840 900 970 1,010 1,060 1,105 1,145 1,185 1,230 1,270 1,305 4½ 32.66 6.54 7.00-15L… 760 855 950 1,025 1,100 1,145 1,190 1,235 1,280 1,325 1,375 1,420 1,460 5 33.85 7.01 “Super Low Section” Sizes 145-10/5.95-10… 380 430 475 515 550 580 605 630 650 675 700 725 745 4 24.76 5.79 125-12/5.35-12… 335 380 420 450 485 510 535 550 570 590 610 630 650 3½ 24.68 5.00 135-12/5.65-12… 370 420 465 505 540 570 590 620 640 665 690 710 730 4 25.53 5.39 145-12/5.95-12… 440 495 550 595 640 665 700 730 755 785 810 840 865 4 26.69 5.79 155-12/6.15-12… 485 545 605 655 705 735 775 805 835 865 895 925 950 4½ 27.36 6.18 135-13/5.65-13… 415 470 520 555 595 625 655 685 710 735 760 785 810 4 26.53 5.39 145-13/5.95-13… 470 525 585 620 670 705 745 770 800 825 855 885 910 4 27.61 5.79 155-13/6.15-13 515 575 610 700 750 780 820 850 880 910 945 975 1,005 4½ 28.44 6.18 165-13/6.45-13… 575 645 715 770 825 865 905 935 970 1,005 1,040 1,075 1,105 4½ 29.52 6.57 175-13/6.95-13… 635 715 795 845 915 955 1,005 1,045 1,085 1,120 1,160 1,200 1,235 5 30.34 7.01 185-13/7.35-13… 695 785 870 945 1,010 1,060 1,115 1,160 1,205 1,245 1,290 1,335 1,370 5½ 31.41 7.40 135-14/5.65-14… 440 495 550 595 640 665 700 730 755 785 810 840 865 4 27.54 5.59 145-14/5.95-14… 495 560 620 665 715 750 785 815 845 875 905 935 965 4 28.54 5.79 155-14/6.15-14… 540 610 675 730 780 825 860 895 925 960 995 1,030 1,060 4½ 29.45 6.18 125-15/5.35-15… 395 445 495 535 570 600 625 650 675 700 720 745 770 3½ 27.69 5.00 135-15/5.65-15… 460 520 575 610 660 690 720 750 775 805 835 860 885 4 28.53 5.39 145-15/5.95-15… 520 585 650 710 760 790 830 860 890 925 955 985 1,015 4 29.54 5.79 155-15/6.35-15… 585 660 730 780 835 875 915 950 985 1,020 1,055 1,090 1,125 4½ 30.45 6.18 175-15/7.15-15… 705 795 880 955 1,020 1,070 1,125 1,170 1,215 1,255 1,300 1,345 1,385 5 32.42 7.01 165-14… 650 715 770 815 880 925 970 1,000 1,035 1,080 1,115 1,145 1,170 4½ 31.22 6.57 175-14… 715 780 850 915 980 1,025 1,070 1,115 1,160 1,200 1,235 1,270 1,310 5 32.13 7.01 185-14… 805 870 940 1,000 1,080 1,135 1,190 1,235 1,290 1,325 1,370 1,400 1,435 5½ 33.15 7.40 195-14… 860 950 1,025 1,105 1,180 1,235 1,290 1,345 1,400 1,445 1,490 1,535 1,580 5½ 34.18 7.80 205-14… 940 1,025 1,115 1,190 1,270 1,335 1,400 1,455 1,510 1,565 1,610 1,655 1,700 6 34.84 8.19 215-14… 1,015 1,115 1,200 1,290 1,380 1,445 1,520 1,590 1,640 1,700 1,740 1,785 1,830 6 35.75 8.58 225-14… 1,080 1,180 1,280 1,380 1,465 1,540 1,620 1,700 1,750 1,810 1,850 1,915 1,970 6½ 36.69 8.98 165-15… 685 750 805 860 915 970 1,015 1,060 1,105 1,135 1,180 1,200 1,235 4½ 31.73 6.57 185-15… 815 905 970 1,050 1,115 1,180 1,235 1,280 1,325 1,370 1,410 1,445 1,490 5½ 33.59 7.40 195-15… 880 970 1,050 1,135 1,215 1,280 1,335 1,390 1,445 1,490 1,535 1,580 1,620 5½ 34.61 7.80 205-15… 970 1,060 1,145 1,225 1,300 1,370 1,445 1,500 1,565 1,610 1,665 1,720 1,765 6 35.79 8.19 215-15… 1,050 1,145 1,235 1,335 1,435 1,500 1,590 1,640 1,700 1,740 1,800 1,850 1,910 6 37.24 8.58 235-15… 1,150 1,295 1,435 1,545 1,660 1,735 1,825 1,895 1,965 2,035 2,110 2,180 2,245 6½ 38.26 9.37 5.0-15… 460 520 575 610 660 690 720 750 775 805 835 860 885 4 28.53 5.39 5.5-15… 520 585 650 710 760 790 830 860 890 925 955 985 1,015 4 29.54 5.79 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-D TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR DASH(-) RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 145-10… 495 525 545 565 585 605 625 640 655 670 685 700 710 4 24.76 5.79 125-12… 405 430 445 465 480 495 505 525 535 550 560 575 580 3½ 24.68 5.00 135-12… 480 510 530 550 565 585 600 620 635 650 665 675 685 4 25.53 5.39 145-12… 570 605 625 650 675 695 715 740 760 775 790 805 815 4 26.69 5.79 155-12… 630 670 695 720 745 770 795 820 840 860 875 890 905 4½ 27.36 6.18 135-13… 515 545 565 590 610 630 650 670 690 705 715 730 740 4 26.53 5.39 145-13… 605 640 665 695 720 740 765 790 815 830 845 855 870 4 27.61 5.79 155-13… 670 710 735 765 790 815 840 870 895 910 925 940 955 4½ 28.44 6.18 165-13… 700 750 800 850 890 930 970 1,010 1,050 1,090 1,130 1,170 1,200 4½ 29.52 6.57 175-13 … 810 860 920 980 1,040 1,100 1,150 1,200 1,240 1,300 1,350 4½ 30.30 6.75 185-13 … 870 940 1,010 1,080 1,140 1,210 1,270 1,330 1,390 1,450 1,510 5 31.42 7.25 195-13 … 970 1,040 1,110 1,180 1,250 1,320 1,400 1,450 1,520 1,580 1,640 5½ 32.38 7.70 135-14… 555 585 610 635 655 675 695 720 740 750 765 780 790 4 27.54 5.39 145-14… 645 680 710 735 760 785 810 840 865 885 905 920 935 4 28.54 5.79 155-14… 630 680 720 760 800 840 880 920 950 980 1,010 1,040 1,070 4½ 29.45 6.18 165-14… 740 790 840 890 940 980 1,020 1,060 1,100 1,140 1,180 1,220 1,250 4½ 30.53 6.57 175-14 … 830 900 960 1,030 1,100 1,160 1,230 1,280 1,350 1,400 1,470 5 31.63 7.00 185-14 … 920 1,000 1,070 1,140 1,220 1,290 1,360 1,420 1,500 1,560 1,640 5 32.59 7.30 195-14 … 1,020 1,100 1,180 1,270 1,340 1,420 1,500 1,570 1,650 1,720 1,800 5½ 33.69 7.80 205-14 … 1,100 1,180 1,270 1,380 1,350 1,540 1,620 1,700 1,770 1,860 1,940 6 34.82 8.80 215-14 … 1,200 1,300 1,390 1,510 1,580 1,670 1,770 1,850 1,920 2,010 2,100 6 35.79 8.60 225-14 … 1,320 1,420 1,510 1,610 1,710 1,800 1,900 1,970 2,050 2,150 2,230 6½ 36.44 8.95 125-15… 495 525 545 565 585 605 625 640 655 670 685 700 710 3½ 27.69 5.00 135-15… 585 620 645 670 695 715 735 755 775 795 810 825 840 4 28.53 5.39 145-15… 680 720 750 780 805 830 855 875 895 920 940 960 975 4 29.54 5.79 155-15… 740 785 815 850 880 905 930 955 980 1,005 1,025 1,045 1,060 4½ 30.45 6.18 165-15… 770 820 870 920 970 1,020 1,070 1,110 1,150 1,190 1,230 1,270 1,310 4½ 31.45 6.57 175-15 … 990 1,050 1,100 1,150 1,200 1,250 1,300 1,350 1,400 1,440 1,480 5 32.41 7.00 180-15… 925 980 1,020 1,060 1,095 1,130 1,170 1,190 1,230 1,260 1,280 1,305 1,325 4½ 32.04 6.62 185-15 … 1,000 1,070 1,140 1,210 1,280 1,350 1,420 1,480 1,540 1,600 1,660 5½ 33.58 7.45 195-15 … 1,080 1,160 1,240 1,330 1,400 1,470 1,550 1,620 1,680 1,760 1,820 5½ 34.22 7.65 205-15 … 1,190 1,280 1,370 1,450 1,530 1,620 1,700 1,760 1,840 1,920 2,000 6 35.20 8.10 215-15 … 1,280 1,380 1,480 1,570 1,660 1,760 1,860 1,940 2,020 2,100 2,200 6 36.00 8.35 220-15 … 1,320 1,420 1,520 1,610 1,695 1,785 1,875 1,960 2,050 2,135 2,225 6 36.49 8.35 225-15 … 1,370 1,470 1,580 1,670 1,780 1,880 1,980 2,060 2,150 2,240 2,340 6½ 36.94 8.80 230-15 … 1,405 1,515 1,625 1,725 1,825 1,925 2,020 2,110 2,190 2,280 2,360 6½ 37.30 8.80 235-15 … 1,430 1,540 1,640 1,750 1,850 1,960 2,060 2,160 2,250 2,350 2,450 6½ 37.75 9.05 240-15 … 1,455 1,570 1,680 1,790 1,890 1,990 2,090 2,190 2,280 2,380 2,480 6½ 38.28 9.05 185-16 … 1,140 1,210 1,270 1,330 1,390 1,450 1,500 1,550 1,600 1,650 1,700 5½ 34.14 7.40 165-400… 800 860 920 980 1,030 1,080 1,130 1,180 1,220 1,260 1,300 1,340 1,380 4.65 32.04 6.62 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-E TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “77 SERIES” BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) G77-14 … 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.04 8.45 5.9-10… 385 430 475 515 550 580 605 630 660 675 700 … 4 24.00 5.80 5.9-12… 460 505 550 595 640 665 700 730 755 785 810 … 4 26.00 5.90 6.2-12… 485 545 605 655 705 735 775 805 835 865 895 925 950 4 27.21 6.06 6.2-13… 515 575 640 700 750 780 820 850 880 910 945 975 1,005 4 28.19 6.06 6.5-13… 575 645 715 770 825 865 905 935 970 1,005 1,040 1,075 1,105 4½ 29.18 6.54 6.9-13… 635 715 795 845 915 955 1,005 1,045 1,085 1,120 1,160 … 4½ 29.92 6.77 6.2-15… 585 660 730 780 835 875 915 950 985 1,020 1,055 1,090 1,125 4 30.17 6.06 6.9-15… 705 795 880 955 1,020 1,070 1,125 1,170 1,215 1,255 1,300 1,345 1,385 4½ 31.93 6.77 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-F TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR TYPE “R” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 5.20R10… 435 460 485 510 535 560 585 615 635 660 685 710 735 3½ 24.84 5.20 5.00R12… 480 495 515 535 555 575 595 615 635 650 670 690 710 3½ 25.62 5.04 5.20R12… 515 540 565 590 615 640 665 695 715 740 765 790 815 3½ 26.79 5.20 5.50R12… 520 545 570 595 620 650 670 705 725 750 775 800 825 4 26.93 5.59 5.60R12… 600 630 655 685 715 740 770 800 825 850 875 905 930 4 27.83 5.71 5.00R13… 535 555 575 590 615 630 650 670 690 705 725 745 765 3½ 26.64 5.04 5.20R13… 570 595 620 645 670 695 720 750 770 795 820 845 870 3½ 27.72 5.20 5.50R13… 575 600 625 650 675 695 725 750 775 795 825 850 875 4 27.95 5.59 5.60R13… 655 685 710 740 765 795 825 855 880 905 935 960 990 4 28.92 5.71 6.00R13… 675 705 735 760 790 815 845 875 900 925 950 975 1,005 4 29.37 6.00 5.90R13… 705 780 805 830 860 885 915 940 965 990 1,015 1,045 1,070 4 29.74 5.91 6.40R13… 810 840 870 905 940 970 1,005 1,040 1,070 1,100 1,135 1,165 1,200 4½ 31.26 6.42 6.50R13… 800 830 860 890 925 960 995 1,030 1,060 1,090 1,120 1,150 1,180 4½ 30.75 6.60 6.70R13… 690 775 860 935 1,000 1,045 1,090 1,135 1,175 1,220 1,260 1,305 1,340 4½ 32.14 6.69 7.00R13… 870 910 950 985 1,025 1,060 1,100 1,145 1,175 1,215 1,255 1,295 1,335 5 31.88 7.10 7.25R13… 940 980 1,020 1,060 1,100 1,135 1,175 1,215 1,255 1,290 1,330 1,370 1,410 5 32.51 7.24 5.20R14… 605 640 670 700 730 760 795 830 855 885 915 950 980 3½ 28.89 5.20 5.90R14… 750 785 815 845 875 905 935 970 995 1,025 1,055 1,085 1,115 4 30.76 5.91 7.00R14… 925 960 1,000 1,040 1,075 1,115 1,155 1,195 1,235 1,270 1,320 1,350 1,380 5 32.88 7.10 7.50R14… 1,065 1,100 1,140 1,180 1,220 1,260 1,300 1,340 1,380 1,415 1,460 1,500 1,540 5½ 34.19 7.65 5.60R15… 705 780 805 830 860 885 915 940 965 990 1,015 1,045 1,070 4 30.87 5.71 6.40R15… 885 925 965 1,005 1,040 1,080 1,120 1,160 1,200 1,235 1,275 1,310 1,350 4½ 33.26 6.42 6.70R15… 975 1,015 1,055 1,095 1,130 1,170 1,215 1,255 1,290 1,325 1,365 1,405 1,445 4½ 33.95 7.00 7.60R15… 1,160 1,200 1,245 1,285 1,325 1,370 1,415 1,465 1,500 1,535 1,575 1,610 1,655 5½ 36.00 7.90 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-G TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) AR70-13… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 5 30.04 7.15 BR70-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 5½ 31.04 7.60 CR70-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 31.65 7.85 DR70-13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.29 8.05 CR70-14… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5½ 32.23 7.65 DR70-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.78 7.90 ER70-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.42 8.10 FR70-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6 34.34 8.55 GR70-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.12 8.85 HR70-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6½ 36.31 9.40 JR70-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 36.86 9.55 LR70-14… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6½ 37.59 9.80 DR70-15… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 33.34 7.75 ER70-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.91 7.95 FR70-15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6 34.87 8.40 GR70-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.65 8.65 HR70-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6½ 36.83 9.20 JR70-15… 1,260 1,350 1,430 1,500 1,580 1,660 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 37.31 9.40 KR70-15… 1,290 1,380 1,460 1,540 1,620 1,690 1,770 1,830 1,900 1,970 2,030 2,090 2,150 6½ 37.62 9.50 LR70-15… 1,340 1,430 1,520 1,600 1,680 1,760 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6½ 38.06 9.65 MR70-15… 1,420 1,520 1,610 1,700 1,780 1,860 1,940 2,020 2,090 2,160 2,230 2,300 2,370 7 38.93 10.15 1 The letters “HR”, “SR” or “VR” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-H TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR TYPE “R” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 145R10… 465 495 525 550 580 605 630 655 680 700 725 750 770 4 24.76 5.79 125R12… 370 400 430 450 475 495 515 535 555 575 595 610 630 3½ 24.68 5.00 135R12… 440 475 505 535 560 585 610 635 655 680 700 725 745 4 25.53 5.39 145R12… 530 565 600 635 665 695 725 755 780 810 835 860 885 4 26.69 5.79 155R12… 590 630 665 700 735 770 800 835 865 895 925 950 980 4½ 27.36 6.18 135R13… 480 515 545 575 600 630 655 680 705 730 755 780 800 4 26.53 5.39 145R13… 590 630 665 700 735 770 800 835 860 890 920 950 980 4 27.59 5.79 155R13… 645 690 730 770 810 845 885 915 950 985 1,015 1,045 1,075 4½ 28.44 6.18 165R13… 680 730 770 820 860 900 930 970 1,010 1,040 1,080 1,110 1,140 4½ 29.18 6.40 175R13… 790 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 30.30 6.75 185R13… 870 930 980 1,030 1,080 1,130 1,180 1,230 1,270 1,310 1,360 1,400 1,440 5 31.42 7.25 195R13… 955 1,010 1,060 1,110 1,170 1,220 1,280 1,320 1,370 1,420 1,470 1,510 1,550 5½ 32.38 7.70 135R14… 515 550 585 615 645 675 705 730 760 785 810 835 860 4 27.54 5.39 145R14… 595 635 675 715 750 785 815 850 880 910 940 965 995 4 28.54 5.79 155R14… 690 740 780 820 860 900 940 970 1,010 1,040 1,080 1,110 1,140 4 29.51 6.05 165R14… 760 810 860 910 960 1,000 1,040 1,080 1,120 1,160 1,200 1,240 1,270 4½ 30.65 6.55 175R14… 840 900 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,310 1,350 1,390 5 31.63 7.00 185R14… 920 980 1,040 1,100 1,160 1,210 1,260 1,310 1,360 1,400 1,450 1,490 1,540 5 32.59 7.30 195R14… 1,020 1,090 1,150 1,210 1,270 1,330 1,390 1,440 1,500 1,550 1,600 1,650 1,690 5½ 33.69 7.80 205R14… 1,110 1,190 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,670 1,730 1,780 1,830 6 34.82 8.30 215R14… 1,210 1,290 1,360 1,430 1,510 1,580 1,640 1,710 1,770 1,830 1,890 1,950 2,000 6 35.79 8.60 225R14… 1,270 1,350 1,430 1,510 1,580 1,660 1,730 1,790 1,860 1,920 1,990 2,050 2,100 6½ 36.44 8.95 125R15… 460 490 520 550 575 605 630 655 680 705 725 745 770 3½ 27.69 5.00 135R15… 545 580 615 650 680 715 745 775 800 830 855 880 910 4 28.53 5.39 145R15… 640 680 720 760 795 830 865 900 935 965 995 1,025 1,055 4 29.54 5.79 155R15… 690 735 780 825 865 905 940 980 1,015 1,050 1,085 1,115 1,150 4½ 30.45 6.18 165R15… 770 820 870 910 960 1,000 1,050 1,090 1,130 1,170 1,200 1,240 1,270 4½ 31.18 6.40 175R15… 840 900 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,390 5 32.30 6.90 185R15… 950 1,010 1,070 1,130 1,180 1,240 1,290 1,340 1,390 1,440 1,480 1,530 1,570 5½ 33.58 7.45 195R15… 1,020 1,090 1,150 1,210 1,270 1,330 1,380 1,440 1,490 1,540 1,590 1,640 1,690 5½ 34.22 7.65 205R15… 1,100 1,170 1,240 1,300 1,370 1,430 1,490 1,550 1,610 1,660 1,720 1,770 1,820 6 35.20 8.10 215R15… 1,190 1,270 1,340 1,410 1,480 1,550 1,620 1,680 1,740 1,800 1,860 1,920 1,970 6 36.00 8.35 225R15… 1,270 1,350 1,430 1,510 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 36.94 8.80 235R15… 1,340 1,430 1,510 1,600 1,680 1,750 1,830 1,900 1,970 2,030 2,100 2,160 2,230 6½ 37.75 9.05 206R16… 1,100 1,170 1,240 1,300 1,370 1,430 1,490 1,550 1,610 1,660 1,720 1,770 1,820 6 36.52 8.19 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-J TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “78 SERIES” BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) A78-13… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 29.74 6.60 B78-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 5 30.72 7.05 C78-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5½ 31.56 7.45 D78-13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.18 7.70 A78-14… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 30.31 6.45 B78-14… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 31.04 6.65 C78-14… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 31.95 7.05 D78-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5 32.52 7.35 E78-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.29 7.65 F78-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 5½ 34.04 7.90 G78-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.02 8.35 H78-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 36.06 8.70 J78-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6 36.58 8.80 A78-15… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 30.85 6.35 C78-15… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 32.45 6.95 D78-15… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5 33.05 7.15 E78-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5 33.65 7.35 F78-15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 5½ 34.56 7.70 G78-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 5½ 35.36 8.05 H78-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 36.50 8.55 J78-15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6 37.02 8.70 L78-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6 37.73 8.85 N78-15… 1,500 1,600 1,700 1,790 1,880 1,970 2,050 2,130 2,210 2,280 2,360 2,430 2,500 7 39.50 9.80 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-K TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) A60-13… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 5½ 30.00 7.85 B60-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 6 30.95 8.35 C60-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6 31.58 8.60 D60-13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 6 32.20 8.85 B60-14… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 5½ 31.26 8.00 C60-14… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6 32.09 8.45 D60-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 6 32.72 8.65 E60-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 7 33.69 9.30 F60-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 7 34.44 9.55 G60-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 7 35.23 9.85 H60-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 7 36.20 10.25 J60-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 7 36.70 10.45 L60-14… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 8 37.83 11.10 B60-15… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 5½ 31.85 7.80 C60-15… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6 32.66 8.25 E60-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 6 33.83 8.70 F60-15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6½ 34.75 9.40 G60-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 7 35.73 9.70 H60-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 7 36.70 10.05 J60-15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 7 37.20 10.25 L60-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 7 37.91 10.50 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-L TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” CANTILEVERED SIDEWALL TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) E50C-16 … 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 3½ 33.31 7.95 F50C-16 … 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,500 1,610 1,650 1,700 3½ 34.04 8.20 G50C-17 … 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 3½ 35.34 8.45 H50C-17 … 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 3½ 36.30 8.80 L50C-18 … 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 3½ 38.00 9.10 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-M TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “78 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) AR78-13… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 29.55 6.50 BR78-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 30.31 6.75 CR78-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 31.13 7.15 AR78-14… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 30.08 6.40 BR78-14… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 30.84 6.60 CR78-14… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 31.67 7.00 DR78-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5 32.26 7.20 ER78-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5 32.86 7.40 FR78-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 5½ 33.78 7.85 GR78-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 34.78 8.30 HR78-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 35.77 8.60 JR78-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 36.47 8.95 AR78-15… 720 770 810 860 900 940 980 1,020 1,060 1,090 1,130 1,160 1,200 4½ 30.66 6.25 BR78-15… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 31.38 6.45 CR78-15… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 5 32.24 6.85 ER78-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.58 7.45 FR78-15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 5½ 34.28 7.70 GR78-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.30 8.15 HR78-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 6 36.23 8.45 JR78-15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 6½ 36.98 8.80 KR78-15… 1,290 1,380 1,460 1,540 1,620 1,690 1,770 1,830 1,900 1,970 2,030 2,090 2,150 6 37.03 8.70 LR78-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 6½ 37.66 9.00 MR78-15… 1,420 1,520 1,610 1,700 1,780 1,860 1,940 2,020 2,090 2,160 2,230 2,300 2,370 6½ 38.35 9.20 NR78-15… 1,500 1,600 1,700 1,790 1,880 1,970 2,050 2,130 2,210 2,280 2,360 2,430 2,500 7 39.17 9.71 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-N TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 155/70R13… 630 650 665 685 705 725 740 760 780 800 820 835 855 4 27.17 5.93 155/70R15… 690 710 730 750 770 790 810 830 850 870 890 910 930 4 29.20 5.93 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-O TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “LOW SECTION” TYPE “R” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 140R12… 490 520 550 580 610 640 660 690 710 740 770 4 26.20 5.40 150R12… 570 610 640 670 700 730 760 790 820 850 880 4 27.19 5.75 150R13… 600 640 680 720 750 780 810 840 870 900 940 4 28.17 5.75 160R13… 670 700 740 780 820 860 900 940 980 1,010 1,040 4½ 29.23 6.25 170R13… 720 760 800 840 880 920 960 1,000 1,00 1,080 1,110 5 30.08 6.60 150R14… 640 670 710 750 780 820 860 900 940 970 1,000 4 29.16 5.75 180R15… 920 970 1,020 1,070 1,120 1,170 1,230 1,280 1,330 1,380 1,430 5 32.97 6.85 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-P TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR SERIES 45 CANTILEVERED SIDEWALL TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) G45C-16… 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 5 35.53 9.70 1 The letter “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-R TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) CR60-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6 31.58 8.60 DR60-14… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 6 32.72 8.65 ER60-14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 6½ 33.50 9.10 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-S TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 235/60R13… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 6 32.81 9.05 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-T TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 205/70R13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 32.29 8.05 205/70R14… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.42 8.10 215/70R14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6 34.34 8.55 225/70R14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.12 8.85 195/70R15… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 5½ 33.34 7.75 205/70R15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 5½ 33.91 7.95 215/70R15… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 6 34.87 8.40 225/70R15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 6 35.65 8.65 1 The letter “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-U TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” CANTILEVERED TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) B60C-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 4½ 30.41 7.65 C60C-15… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 4 31.92 7.35 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-V TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” BIAS PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) B50-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 6 30.84 9.15 C50-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6½ 3 .48 9.40 D50-13… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 6½ 32.29 9.85 F50-14… 1,020 1,090 1,160 1,220 1,280 1,340 1,400 1,450 1,500 1,550 1,610 1,650 1,700 7 34.10 10.20 G50-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,690 1,730 1,780 1,930 8 35.29 10.95 H50-14… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 8 36.24 11.35 M50-14… 1,420 1,520 1,616 1,700 1,780 1,860 1,940 2,020 2,090 2,160 2,230 2,300 2,370 9 38.51 12.55 N50-14… 1,500 1,600 1,700 1,790 1,880 1,970 2,050 2,130 2,210 2,280 2,360 2,430 2,500 9 39.17 12.85 F50-15… 950 1,010 1,070 1,130 1,190 1,240 1,300 1,350 1,400 1,440 1,490 1,540 1,580 6½ 33.74 9.50 G50-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 7 35.38 10.35 H50-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 8 36.76 11.15 L50-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,830 1,900 1,970 2,040 2,100 2,170 2,230 8 31.94 11.65 N50-15… 1,500 1,600 1,700 1,790 1,880 1,970 2,050 2,130 2,210 2,280 2,360 2,430 2,500 9 39.65 12.65 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-W TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) BR50-13… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 6½ 30.84 9.15 CR50-13… 840 890 950 1,000 1,050 1,100 1,140 1,190 1,230 1,270 1,320 1,360 1,400 6½ 31.48 9.40 GR50-14… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 8 35.29 10.95 JR50-14… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 8 36.74 11.60 GR50-15… 1,100 1,180 1,250 1,310 1,380 1,440 1,500 1,560 1,620 1,680 1,730 1,780 1,830 7 35.38 10.35 HR50-15… 1,200 1,290 1,360 1,440 1,510 1,580 1,650 1,710 1,770 1,830 1,890 1,950 2,010 8 36.76 11.15 JR50-15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,780 1,860 1,920 1,980 2,040 2,100 8 37.24 11.35 LR50-15… 1,340 1,430 1,520 1,600 1,680 1,750 1,820 1,900 1,970 2,040 2,100 2,170 2,230 8 37.94 11.65 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-X TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 195/50R15… 650 690 730 770 810 850 890 920 955 990 1,020 1,050 1,080 6 30.16 7.91 225/50R16… 880 940 1,000 1,060 1,110 1,160 1,210 1,255 1,300 1,345 1,390 1,435 1,475 6½ 33.34 8.98 285/50R15… 1,260 1,350 1,430 1,500 1,580 1,650 1,720 1,790 1,860 1,920 1,980 2,040 2,100 8 36.84 11.26 265/50R16… 1,160 1,235 1,310 1,385 1,450 1,520 1,580 1,645 1,709 1,765 1,820 1,875 1,930 8 36.55 10.71 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-Y TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR ALL MILLIMETRIC “65 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 195/65R350… 815 860 905 950 990 1,030 1,070 1,115 1,155 1,195 1,235 1,275 1,315 105 30.70 7.48 205.65R375… 920 970 1,020 1,070 1,120 1,170 1,220 1,265 1,310 1,355 1,400 1,445 1,490 105 32.65 7.76 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-AA TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “P/80” ISO TYPE TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) P155/80R13 3… 660 705 740 760 795 825 860 880 905 935 960 980 1,005 4½ 28.46 6.18 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “80”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
3 The letters “D” for diagonal and “B” for belted may be used in place of the “R”.
TABLE I-BB TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “40 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 285/40R15… 890 950 1,010 1,070 1,120 1,170 1,220 1,270 1,320 1,360 1,410 1,450 1,490 9½ 37.42 11.22 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-CC TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “35 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 345-35R15… 960 1,030 1,090 1,150 1,210 1,270 1,320 1,370 1,420 1,470 1,520 1,560 1,610 11½ 37.42 13.58 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-DD TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “55 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 205/55R16… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 6 32.57 8.19 225/55R13… 830 890 940 980 1,030 1,080 1,120 1,160 1,200 1,240 1,280 1,320 1,350 6 30.98 8.78 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-EE TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “45 SERIES” RADIAL PLY TIRES
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) 235/45R15… 780 840 890 930 980 1,030 1,070 1,110 1,150 1,190 1,230 1,270 1,300 8 32.11 9.29 1 The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
TABLE I-FF TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “P/70 SERIES” ISO TYPE TIRES, STANDARD LOAD
Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.) Test rim Minimum Section width size factor width 2 Tire size designation 1 16 18 20 22 24 26 28 30 32 34 36 38 40 (inches) (inches) (inches) P20570R13 3… 870 925 980 1025 1070 1115 1155 1200 1235 1280 1310 1345 1390 5½ 31.73 7.99 1 The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.
2 Actual section width and overall width shall not exceed the specified section width by more than 7 percent.
3 The letters “D” for diagonal and “B” for belted may be used in place of the “R”.